Tienda
Close
250FT/250G PLA 3D INK® $16 EA Cobalt
PLA 3D Ink® is polylactic acid, a non-toxic biodegradable thermoplastic and one of the most commonly used 3D printing materials.
Close
250FT/250G PLA 3D INK® $16 EA Crystal clear
PLA 3D Ink® is polylactic acid, a non-toxic biodegradable thermoplastic and one of the most commonly used 3D printing materials.
5MP Night Vision Camera for Raspberry Pi
INTRODUCTION This 5MP Night Vision Camera for Raspberry Pi is compatible with every version of Raspberry Pi, and comes with
Close
Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout – BNO055
DESCRIPTION If you’ve ever ordered and wire up a 9-DOF sensor, chances are you’ve also realized the challenge of turning
Close
Adaptador MicroHDMI a HDMI
Adaptador de microHDMI a HDMI, el Raspberry Pi 4 tiene entrada MicroHDMI, por lo que si tienes una pantalla con hable HDMI-HDMI, con este adaptador solucionas el problema y los puedes conectar sin problemas.
Close
Analog Infrared CO2 Sensor For Arduino (0~5000 ppm)
INTRODUCTION The concentration of carbon dioxide (0.03% usuallly) is related to daily life. Recently, there’s a study showing that the
Close
Antena 2.4Ghz para XBee S2C o XBee3 RPSMA 3dBi
Antena de 3dBi para los XBee RPSMA de 2.4Ghz, de los productos que tenemos esta antena es compatible con:
- XBee S2C RPSMA
- XBee Pro S2C RPSMA
- XBee S3 RPSMA
- XBee S3 Pro RPSMA
Close
Antena 900Mhz para XBee S3B RPSMA 3dBi
Description: 900MHz Duck Antenna 3dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 200mm long.
The FCC is moving towards Part 15 compliance. All this means is that all the SMA RF connectors are changing gender. Really annoying for those of us who need to mate an antenna to an RF device. The FCC gender change was instituted to prevent home users from damaging RF equipment (think home WiFi) when screwing on an antenna. If all antennas are female, there is no way to damage the center connector. However, you have to be very sure now what kind of SMA connector you need.
Documents:
Close
Arduino DUE Original
Arduino DUE version italiana, aqui sus caracteristicas: Microcontroller AT91SAM3X8E Operating Voltage 3.3V Input Voltage (recommended) 7-12V Input Voltage (limits) 6-16V
Close
Arduino M0
Descripcion: With the new Arduino M0 board, the more creative individual will have the potential to create one’s most imaginative and new
Close
Arduino Mega R3 Original
Arduino Mega en su versión original, entre sus principales características tenemos:
| Microcontroller | ATmega2560 |
| Operating Voltage | 5V |
| Input Voltage (recommended) | 7-12V |
| Input Voltage (limit) | 6-20V |
| Digital I/O Pins | 54 (of which 15 provide PWM output) |
| Analog Input Pins | 16 |
| DC Current per I/O Pin | 20 mA |
| DC Current for 3.3V Pin | 50 mA |
| Flash Memory | 256 KB of which 8 KB used by bootloader |
| SRAM | 8 KB |
| EEPROM | 4 KB |
| Clock Speed | 16 MHz |
| LED_BUILTIN | 13 |
| Length | 101.52 mm |
| Width | 53.3 mm |
| Weight | 37 g |
Close
Close
Arduino MKR WiFi 1010
The Arduino MKR WiFi 1010 is the easiest point of entry to basic IoT and pico-network application design. Whether you
Close
Arduino Starter Kit Original (Incluye libro en español)
El Kit incluye: 1 Projects Book (170 pages), 1 Arduino / Genuino Uno, 1 USB cable, 1 Breadboard 400 points, 70Solid core jumper
Close
Arduino UNO R3 Original
Versión Original Italiana del Arduino UNO.
Entre las principales características tenemos:
| Microcontroller | ATmega328P |
| Operating Voltage | 5V |
| Input Voltage (recommended) | 7-12V |
| Input Voltage (limit) | 6-20V |
| Digital I/O Pins | 14 (of which 6 provide PWM output) |
| PWM Digital I/O Pins | 6 |
| Analog Input Pins | 6 |
| DC Current per I/O Pin | 20 mA |
| DC Current for 3.3V Pin | 50 mA |
| Flash Memory | 32 KB (ATmega328P) of which 0.5 KB used by bootloader |
| SRAM | 2 KB (ATmega328P) |
| EEPROM | 1 KB (ATmega328P) |
| Clock Speed | 16 MHz |
| LED_BUILTIN | 13 |
| Length | 68.6 mm |
| Width | 53.4 mm |
| Weight | 25 g |
Ardupilot APM 2.8
Ardupilot, tarjeta controladora para manejar un drone, necesita del software Mission Planner para su manejo.
